OMEGA Experimental Operations

System Description

System Description
Document Name	Procedure ID
OMEGA System Operations Manual Volume I–System Description	S-AA-M-12
Omega Target Positioning System Descriptions	S-AA-M-024
OMEGA Target Viewing System System Description	S-AA-M-023
Target Chamber Recovery System Refresher Presentation	Q-TR-M-009
Target Chamber Recovery System Description
Experimental Diagnostics
Targets and Target Fabrication

Shot Procedures

Shot Procedures
Section	Document Name	Procedure ID
ESO	Omega Type 5 and EP Type 7 Shot Checklist	S-OM-M-008
	Target Shot Procedure for Ambient Temp Targets	S-OM-M-009
	Target Shot Procedure for Spherical Cryo	S-OM-M-010
	Target Shot Procedure for Planar MC (normal pull)	S-OM-M-011
	Target Shot procedure for Planar MC (Shroud Parked)	S-OM-M-059
	Target Shot Procedure for Planar MC (no shroud)	S-OM-M-063
EST	Omega Target Bay Sweep Checklist	S-OM-M-064
Shot Preparation	ESO Shot Preparation Checklist	S-OM-M-007
Securing	ESO Securing Checklist	S-OM-M-065

Startup

Startup
Section	Document Name	Procedure ID
Power Outage	Planned Power Outage Shutdown Procedure	S-OM-P-003
	Planned Power Recovery Procedure	S-OM-P-004
	Unplanned Power Outage Recovery Procedure	S-OM-P-005
Vacuum Systems	Simplicity Vacuum Controls GUI (CIMVAC) Users Manual	D-ES-K-634
	Pump House Operations	S-OM-P-100
	Target Chamber Vacuum Operations	S-OM-P-101
	Omega Beam Transfer Tube Vacuum Operations	S-OM-P-102
	Target Positioning System Operations	S-OM-P-103
Tritium	Diagnostic Tritium Operations	S-OM-P-104
TVS & associated	Target Viewing System	S-OM-P-105
	HSvideo Camera	S-OM-P-106
	Cryo Shroud Sequencing and Target Detection Systems	S-OM-P-107
Cryo	Upper Pylon Procedures	S-OM-P-108
	Cryopump Regeneration	S-OM-P-109
	Cryo Shot Preparation Checklist	S-OM-P-144
OMEGA EP	OAPI/M	S-OM-P-119
OMEGA EP	PAD/FSM	S-OM-P-149
Misc.	OMEGA Target Bay Elevator Operating Procedure	S-OM-P-152
	OMEGA Scintillation Counter Operation Procedure	S-OM-P-159
	OMEGA Target Bay 10-Ton Overhead Crane Operating Procedure	S-OM-P-187
	S.W.I.S.S. Activation Procedure	S-OM-P-201

Troubleshooting

Troubleshooting
Section	Document Name	Procedure ID
Misc	PLC Restart Procedure – Fixed Diagnostics	S-TS-P-002
Misc	TIM Controls Troubleshooting Guide	S-TS-P-004
Misc	LIM Control System Troubleshooting Guide	D-LM-M-239

Maintenance

Maintenance
Section	Document Name	Procedure ID
Personnel Safety Procedures	Bioassay	S-SM-P-113
	Filter Mask Fit Check	S-SM-P-146
	OMEGA Target Chamber Entry Procedure	S-SM-P-395
Radiation Related Procedures	Recover Target Debris from TC Floor	S-SM-P-054
	Sample Target Chamber Environment for Beryllium	S-SM-P-055
	Target Chamber Alpha Swipe	S-SM-P-056
	Assay Exhaust Sample Activity	S-SM-P-071
	Confirm Operation of Overhoff Tritium Air Sampler	S-SM-P-072
	Replace Overhoff TASC Pump & Rotameter / Calibrate Flow	S-SM-P-073
	Inspect Overhoff TASC Dust Filter	S-SM-P-074
	Shield Monitors	S-SM-P-105
	Target Chamber Activation	S-SM-P-106
	Target Bay Activation	S-SM-P-107
	Surface Contamination Survey	S-SM-P-108
	TIM Dry Box Surface Contamination Survey	S-SM-P-109
	TIM Radiation Survey	S-SM-P-110
	TPS-2 Radiation Survey after DT Campaign	S-SM-P-111
	Radioactive Material Inventory Audit	S-SM-P-112
	Ludlum Model 3 Geiger Counter	S-SM-P-118
	Overhoff 7000 SBAyC Tritium Monitor	S-SM-P-119
	Ludlum Model 9 Ion Counter	S-SM-P-120
	Ludlum Model 9 Inspect/Replace Desiccant Packages	S-SM-P-121
	Non-Burnable Solid Radiation Waste Disposal	S-SM-P-445
	Target Bay Be and Tritium Survey	S-SM-P-440
	Tritium Decontamination	S-SM-P-451
Exhaust Stack Procedures	Verify Stack Flowrate	S-SM-P-069
Exhaust Stack Procedures	Calibrate Flowmeter	S-SM-P-070
Target Chamber Vacuum Subsystem Procedures	Inspect Viewing Window for Potential Mechanical Failures	S-SM-P-078
	TC Vacuum Gauge Calibration Check	S-SM-P-058
	EH1200 Blower Oil Levels	S-SM-P-059
	EH1200 Blower Pump Connections	S-SM-P-060
	EH1200 Blower Oil Change	S-SM-P-061
	GV120 Gearbox Oil Level	S-SM-P-062
	GV120 Pipelines and Connections	S-SM-P-063
	GV120 Gearbox Oil & Sight-Glasses	S-SM-P-064
	GV120 Relubricate Rotor Bearings	S-SM-P-065
	GV120 Change Felt Head-Plate Filter	S-SM-P-066
	Check TC Vacuum Pump Exhaust Filters	S-SM-P-181
	CTI On-Board 400 Cryopump Adsorber Change	S-SM-P-068
	Target Chamber RGA Scan	S-SM-P-378
	OMEGA Target Chamber Entry Procedure	S-SM-P-395
Spatial Filter Vacuum Subsystem Procedures	EH500/EH4200 Blower Oil Level	S-SM-P-089
	EH4200 Blower Inspect Pump	S-SM-P-090
	GV600 Blower Oil Level	S-SM-P-091
	GV600 Blower Gas Ballast, Pipes & Connections	S-SM-P-092
	EH500 Blower Lubrication	S-SM-P-093
	EH500/EH4200 Blower Oil Change	S-SM-P-094
	GV600 Blower 18-Month Maintenance	S-SM-P-095
	GV600 Blower Oil Change and Vent Filters	S-SM-P-096
	GV600 Blower Overhaul	S-SM-P-097
	GV600 Blower Replace Pump Motor	S-SM-P-098
	Check/Tighten Spider Manifold Fasteners	S-SM-P-099
	Replace Branch Isolation Valve Seals	S-SM-P-100
Target Viewing System Procedures	TVS-II Illumination Calibration	S-SM-P-370
	TVS-II Calibration Data Collection	S-SM-P-373
	TVS-II Changing TVS Calibration	S-SM-P-390
	TVS-II Shutter Timing Procedure	S-SM-P-381
	TVS-II Imperx Camera Replacement	S-SM-P-371
	TVS Related Software & Equipment Recovery Procedure	S-SM-P-428
Target Positioner Procedures	Shuttle Rotation	S-SM-P-075
	Re-Qualify Back-Up Shuttle	S-SM-P-076
	Stalk Alignment Test	S-SM-P-079
	Replace TPS2 Gate Valve	S-SM-P-080
Ten Inch Manipulator Procedures	Preconditions and Precautions – Install/Remove Break-Out Box	S-SM-P-122
	Check/Tighten External Fasteners	S-SM-P-123
	Check/Tighten Electrical Connections	S-SM-P-124
	Check/Replace Drive Coupler	S-SM-P-125
	Check/Repair Pneumatic Subsystem	S-SM-P-126
	Check/Adjust Door Motions	S-SM-P-127
	Check/Repair Door Seal	S-SM-P-128
	Check/Tighten Internal Fasteners	S-SM-P-129
	Check Valve Seal	w/o TC Entry
	Replace Valve Seal	w/ TC Entry
	Check/Repair Side Rollers	S-SM-P-132
	Repeatability Test	S-SM-P-133
	Leak and Rate of Rise Test	S-SM-P-134
	TIM Monitor Cable Calibration	S-SM-P-145
	TIM Monthly Maintenance	S-SM-P-297
	TIM 6 LOS Mid-Beam Collimator Alignment	S-SM-P-414
	Full TIM Maintenance Checklist	S-SM-P-392
Upper Pylon Procedures	Check and Correct UP Alignment	S-SM-P-153
	Inspect Safety Rack & Engagement Cog	S-SM-P-154
	Linear Motor – Inspect Servo Amplifier Contactors	S-SM-P-155
	Check Vacuum Seal	S-SM-P-156
	Check/Replace Pull Tube Bearings	S-SM-P-157
	Replace Vacuum Seal	S-SM-P-158
	Gripper Inspection	S-SM-P-159
	Gripper Replacement Procedure	S-SM-P-376
	MCTC Shroud Recovery Procedure	S-SM-P-396
Target Diagnostic Procedures	Diagnostic CCD Water Change	S-SM-P-135
	Check Pointing of Neutron Temporal Diagnostic	S-SM-P-136
	CPS Preconditions & Precautions	S-SM-P-137
	CPS Clean and Lube Lead Screw	S-SM-P-138
	CPS Check/Tighten Motor Coupler Screws	S-SM-P-139
	CPS Clean Suie Rails and Bearing Surfaces	S-SM-P-140
	CPS Check/Repair IP O-Ring	S-SM-P-141
	CPS Clean & Wipe Down Interior Surfaces	S-SM-P-142
	Replace IR Fiducial Diode Bias Battery	S-SM-P-143
	Timing Diagnostic Oscilloscope Calibration	S-SM-P-144
	Inspect/Repair XRFC Film Backs	S-SM-P-147
	Inspect/Repair XRFC Nosecones	S-SM-P-148
	XRFC Timing Calibration	S-SM-P-149
	ASBO DI Water Filter Change	S-SM-P-150
	ASBO DI Water Anti-Bacterial Treatment	S-SM-P-151
	ASBO Flashlamp Replacement	S-SM-P-152
	ASBO-SOP T-Zero Timing Procedure	S-SM-P-425
	JOBO Vendor Maintenance	S-SM-P-160
	DANTE Back Flange Maintenance	S-SM-P-365
	DANTE Filter Inspection and Servicing	S-SM-P-366
	DANTE Venting and Pumping	S-SM-P-367
	SCCAL Vacuum Maintenance and Pumpdown	S-SM-P-369
	NDI – MRS Alignment	S-SM-P-377
Crane Procedures	Inspect and Grease Gantry Crane	S-SM-P-101
	Gantry Crane Contract Service	S-SM-P-102
	Inspect and Grease Hydraulic Floor Crane	S-SM-P-103
	Inspect and Grease Mechanical Floor Crane	S-SM-P-104

Diagnostic Status Webpage

Our website is currently under construction. We appreciate your patience during this time.

OMEGA Experimental Operations

Helpful Resources