Maintenance Plans Section 5 - Optomechanical
Subsystem Actions Requiring Shots
- HED Calibration Check (S-SM-P-242)
- HED Calibration (Complete) (S-SM-P-243)
- FCC Tuning Scan (S-SM-P-244)
- FCC Tuning Check (S-SM-P-245)
- HED Burn (S-SM-P-246)
- D Burn (S-SM-P-247)
- UV Focus Scan (S-SM-P-248)
- Reference Best Focus (S-SM-P-249)
Subsystem Actions Without Shots
- Beam Timing Run (S-SM-P-250)
- OMEGA Transport Instrumentation System (OTIS) (S-SM-P-251)
- Blast Window Assembly (BWA) UV Transport (S-SM-P-252)
- Primary Pick-Off (PPO) / DPR Transmission (S-SM-P-253)
- Measure SG4 DPP Transmission (S-SM-P-254)
- Full System Auto Balance (S-SM-P-255)
- Set Splits with Roving Diagnostic (S-SM-P-256)
- Calibrate Calorimeters - Check (S-SM-P-257)
- Calibrate Calorimeters - Calibration Series (S-SM-P-258)
- Two State Control Module (S-SM-P-333)
IR Alignment Procedures
- Check Mirror Wavefront Quality (S-SM-P-259)
- Leg Collimation Check (S-SM-P-260)
- Re-Align A-Rods (S-SM-P-261)
- System Crosshair to A-Out Crosshair (S-SM-P-262)
- A-Out Crosshair to B-In Crosshair (S-SM-P-263)
- Check/Adjust Alignment: B-Split (S-SM-P-264)
- Check Alignment at D-Split Input Fiducials (S-SM-P-265)
- Update F-ASP Coarse Pointing References (S-SM-P-266)
- Check/Correct Alignment of the Stage F Prisms (S-SM-P-267)
- Check SSA Alignment, Level (S-SM-P-268)
- Check Alignment of Spatial Filters (S-SM-P-269)
- Check Level of FCC Rails (S-SM-P-270)
- Spatial Filters - Check Leakage Rate (S-SM-P-271)
- Spatial Filters - Mechanical Checks (S-SM-P-272)
- Check Spatial Filter PHM Electrical Connections (S-SM-P-273)
- Beamline Collimation Check (S-SM-P-274)
- Replace Retro Burn Paper (S-SM-P-275)
- Check Fixed Optic Lockdowns on IRAT (S-SM-P-276)
- Check Fixed Optic Lockdowns on A-Split (S-SM-P-277)
- Check Fixed Optic Lockdowns on B-Split (S-SM-P-278)
- Check Fixed Optic Lockdowns on C-Splits (S-SM-P-279)
- Check Fixed Optic Lockdowns on D-Splits (S-SM-P-280)
- Manual Knife-Edge Pinholes (S-SM-P-281)
- Remote Knife-Edge D, E, F Pinhole Evaluation (S-SM-P-282)
- Check Knife-Edge Diagnostic Calibration (S-SM-P-283)
- LPI Alignment Check (S-SM-P-284)
- Check D-Shutter Limit Switches (S-SM-P-285)
- Reference Crystaks using Second Tripler Alignment Diagnostic (STAD) (S-SM-P-286)
UV Alignment Procedures
- Check/Align HED Spatial Filters (S-SM-P-287)
- Check/Adjust UV Centering DPR In / DPR Out (S-SM-P-288)
- FLAS Retro Check (S-SM-P-289)
- UVAT Alignment Check (S-SM-P-290)
- UVAT Full Alignement (S-SM-P-291)
- Clean and Inspect UVAT Optics (S-SM-P-292)
- Pump Diode Replacement for UVAT I & UVAT II (S-SM-P-293)
- UVAT Collimation Check (S-SM-P-294)
- Clean UVAT I Particulate Filter (S-SM-P-295)
- Check / Adjust UVDT Alignment (S-SM-P-296)
- Operate & Check Out UVAT I & UVAT II (S-SM-P-297)
- Calorimeter Seal Check (S-SM-P-298)
- Check HED Coolant Level (S-SM-P-299)
- Check Burn Paper on Back of F-Cals (S-SM-P-300)
- Verify Alignment of FLAS Retro Fixture (S-SM-P-301)
- Check UVAT II Water Level (S-SM-P-302)
IRAT Procedures
- IRAT Alignment Check (S-SM-P-303)
- IRAT Full Alignment (S-SM-P-304)
- Clean and Inspect Optics (S-SM-P-305)
Long Path Length Adjuster Procedures
- Inspect PLAS (S-SM-P-306)
- Check Mounting Pad Lock-Downs (S-SM-P-307)
- PLAS Mirror Alignment Checks (S-SM-P-308)
- D-Split Mirrors - Coordinate Verification (S-SM-P-309)
Focus Lens Procedures
- FLAS Encoder Mechanical Check (S-SM-P-310)
- Replace Compensation Springs (S-SM-P-311)
- Exercise FLAS Springs (S-SM-P-312)
- Support BWA Change (S-SM-P-313)
- Support Focus Lens Change (S-SM-P-314)
- Support DPP Change (S-SM-P-315)
Periscope Mirror Assembly Procedures
- Inspect/Lubricate RAPIDTRAK Ball Screw (S-SM-P-316)
- Check/Replenish Gearbox Oil (S-SM-P-317)
- Inspect & Lubricate Kinematic Mount Surfaces (S-SM-P-318)
- Lubricate Air Cylinder Clevis Pins (S-SM-P-319)
- Check Pneumatic Filters (S-SM-P-320)
- Inspect Rails (S-SM-P-321)
- Check Fasteners (S-SM-P-322)
- Change Gearbox Oil (S-SM-P-323)
- Change DeMag Trolley Gearbox Oil (S-SM-P-324)
- Verify Function of Safety Features (S-SM-P-325)
- X Travel Calibration (S-SM-P-326)
ASP Procedures
- Inspect and Verify ASP Functionality in the A and C Stages (S-SM-P-327)
- Verify Function and Imaging (S-SM-P-328)
- Inspect Crosshair Stops (S-SM-P-329)