Maintenance Plans Section 1 - Laser Drivers
Laser Driver Subsystem Procedures
- System-Wide Crate Reset (S-SM-P-001)
- Check for Ground Loops (S-SM-P-002)
- IR3 Calibration (S-SM-P-003)
- ACSLv2 Synchronization (S-SM-P-053)
- 12GHz Agilent DSO91204A Calibration Procedure (S-SM-P-397)
- 15 GHz Scope Calibration (S-SM-P-077)
- PGR/DER HVAC Check (S-SM-P-081)
- Master Timing Generator Reset (S-SM-P-161)
Pulse Shaping Procedures
- Modulator Calibration (MODCAL) (S-SM-P-004)
- Modulator Calibration (MINCAL) (S-SM-P-005)
- Exercise Colby(s) (S-SM-P-006)
- 10V PSPL Calibration (S-SM-P-008)
- Koheras Output Power (S-SM-P-009)
- IFES Fiber Amplifier Pump Diode Efficiency (S-SM-P-011)
- Inspect Modulator Cables (S-SM-P-012)
Regen Procedures
- Check DPR Settings (S-SM-P-013)
- DPR Cavity Alignment Check (S-SM-P-015)
- DPR Timing Check (S-SM-P-016)
- Check Isolation Contrast (S-SM-P-017)
- Check Regen Output Energy (S-SM-P-018)
- Pockels Cell Voltage Check (S-SM-P-019)
- Output Collimation Check (S-SM-P-020)
- Regen Output Beam Ellipticity Check (S-SM-P-021)
- Driver Spatial Profile & Beam Size Check (S-SM-P-022)
- Bournlea Halfwave Voltage Output Check (S-SM-P-023)
- G6 Diode Battery Measurement (S-SM-P-024)
- Regen Energy Calibration (S-SM-P-025)
- Beam Timing Support (S-SM-P-027)
- Replace Pockels Cell Driver (S-SM-P-052)
- Check Regen Switch-Out Timing (S-SM-P-389)
LARA Procedures
- LARA Centering Diagnostic Alignment Check (S-SM-P-028)
- LARA Monthly Alignment (S-SM-P-029)
- LARA Ring Pockels Cell Timing Check (S-SM-P-030)
- LARA Isolation Pockels Cell Timing Check (S-SM-P-031)
- LARA Ring Rail Contrast Ratio (S-SM-P-032)
- Driverline Energy Calibration (S-SM-P-033)
- SSD Critical Mirror Alignment (S-SM-P-387)
- LARA Hold-Off Test (S-SM-P-034)
Spatial Filter Procedures
- Spatial Filter Pinhole Visual Inspection (S-SM-P-035)
- Spatial Filter Alignment Check (S-SM-P-036)
- LARA Spatial Filter Pinhole Centering (S-SM-P-037)
- Spatial Filter Pinhole Centering (S-SM-P-038)
- Spatial Filter Drive Belts (S-SM-P-078)
Optics Procedures
Smoothing by Spectral Dispersion Procedures
- Check SSD Modulation (S-SM-P-040)
- SSD Modulator Tuning (Mod1, Mod2) (S-SM-P-041)
- Halfwave Voltage Check on FID Pulser (SSD Slicer) (S-SM-P-042)
- Check SSD Slicer Timing (S-SM-P-388)
Driverline Procedures
- Common Driver Faraday Rotator Contrast Measurement (S-SM-P-043)
- Backlighter Faraday Rotator Contrast Measurement (S-SM-P-046)