OMEGA Laser Facility > Documentation > Volume III Subsystem and Component Maintenance > Section 5 Optomechanical

OMEGA System Operations Manual - Volume III -- Subsystem and Component Maintenance (S-AA-M-014)

Front Matter - Maintenance Index & Schedules - S-OM-P-030

Subsystem Actions Requiring Shots:

S-SM-P-242: HED Calibration Check

S-SM-P-243: HED Calibration (Complete)

S-SM-P-244: FCC Tuning Scan

S-SM-P-245: FCC Tuning Check

S-SM-P-246: HED Burn

S-SM-P-247: D Burn

S-SM-P-248: UV Focus Scan

S-SM-P-249: Reference Best Focus

Subsystem Actions Without Shots :

S-SM-P-250: Beam Timing Run

S-SM-P-251: OMEGA Transport Instrumentation System (OTIS)

S-SM-P-252: Blast Window Assembly (BWA) UV Transport

S-SM-P-253: Primary Pick-Off (PPO) / DPR Transmission

S-SM-P-254: Measure SG4 DPP Transmission

S-SM-P-255: Full System Auto Balance

S-SM-P-256: Set Splits with Roving Diagnostic

S-SM-P-257: Calibrate Calorimeters - Check

S-SM-P-258: Calibrate Calorimeters - Calibration Series

S-SM-P-333: Two State Control Module

IR Alignment Procedures:

S-SM-P-259: Check Mirror Wavefront Quality

S-SM-P-260: Leg Collimation Check

S-SM-P-261: Re-Align A-Rods

S-SM-P-262: System Crosshair to A-Out Crosshair

S-SM-P-263: A-Out Crosshair to B-In Crosshair

S-SM-P-264: Check/Adjust Alignment: B-Split

S-SM-P-265: Check Alignment at D-Split Input Fiducials

S-SM-P-266: Update F-ASP Coarse Pointing References

S-SM-P-267: Check/Correct Alignment of the Stage F Prisms

S-SM-P-268: Check SSA Alignment, Level

S-SM-P-269: Check Alignment of Spatial Filters

S-SM-P-270: Check Level of FCC Rails

S-SM-P-271: Spatial Filters - Check Leakage Rate

S-SM-P-272: Spatial Filters - Mechanical Checks

S-SM-P-273: Check Spatial Filter PHM Electrical Connections

S-SM-P-274: Beamline Collimation Check

S-SM-P-275: Replace Retro Burn Paper

S-SM-P-276: Check Fixed Optic Lockdowns on IRAT

S-SM-P-277: Check Fixed Optic Lockdowns on A-Split

S-SM-P-278: Check Fixed Optic Lockdowns on B-Split

S-SM-P-279: Check Fixed Optic Lockdowns on C-Splits

S-SM-P-280: Check Fixed Optic Lockdowns on D-Splits

S-SM-P-281: Manual Knife-Edge Pinholes

S-SM-P-282: Remote Knife-Edge D, E, F Pinhole Evaluation

S-SM-P-283: Check Knife-Edge Diagnostic Calibration

S-SM-P-284: LPI Alignment Check

S-SM-P-285: Check D-Shutter Limit Switches

S-SM-P-286: Reference Crystaks using Second Tripler Alignment Diagnostic (STAD)

UV Alignment Procedures:

S-SM-P-287: Check/Align HED Spatial Filters

S-SM-P-288: Check/Adjust UV Centering DPR In / DPR Out

S-SM-P-289: FLAS Retro Check

S-SM-P-290: UVAT Alignment Check

S-SM-P-291: UVAT Full Alignement

S-SM-P-292: Clean and Inspect UVAT Optics

S-SM-P-293: Pump Diode Replacement for UVAT I & UVAT II

S-SM-P-294: UVAT Collimation Check

S-SM-P-295: Clean UVAT I Particulate Filter

S-SM-P-296: Check / Adjust UVDT Alignment

S-SM-P-297: Operate & Check Out UVAT I & UVAT II

S-SM-P-298: Calorimeter Seal Check

S-SM-P-299: Check HED Coolant Level

S-SM-P-300: Check Burn Paper on Back of F-Cals

S-SM-P-301: Verify Alignment of FLAS Retro Fixture

S-SM-P-302: Check UVAT II Water Level

IRAT Procedures:

S-SM-P-303: IRAT Alignment Check

S-SM-P-304: IRAT Full Alignment

S-SM-P-305: Clean and Inspect Optics

Long Path Length Adjuster Procedures:

S-SM-P-306: Inspect PLAS

S-SM-P-307: Check Mounting Pad Lock-Downs

S-SM-P-308: PLAS Mirror Alignment Checks

S-SM-P-309: D-Split Mirrors - Coordinate Verification

Focus Lens Procedures:

S-SM-P-310: FLAS Encoder Mechanical Check

S-SM-P-311: Replace Compensation Springs

S-SM-P-312: Exercise FLAS Springs

S-SM-P-313: Support BWA Change

S-SM-P-314: Support Focus Lens Change

S-SM-P-315: Support DPP Change

Periscope Mirror Assembly Procedures:

S-SM-P-316: Inspect/Lubricate RAPIDTRAK Ball Screw

S-SM-P-317: Check/Replenish Gearbox Oil

S-SM-P-318: Inspect & Lubricate Kinematic Mount Surfaces

S-SM-P-319: Lubricate Air Cylinder Clevis Pins

S-SM-P-320: Check Pneumatic Filters

S-SM-P-321: Inspect Rails

S-SM-P-322: Check Fasteners

S-SM-P-323: Change Gearbox Oil

S-SM-P-324: Change DeMag Trolley Gearbox Oil

S-SM-P-325: Verify Function of Safety Features

S-SM-P-326: X Travel Calibration

ASP Procedures:

S-SM-P-327: Inspect and Verify ASP Functionality in the A and C Stages

S-SM-P-328: Verify Function and Imaging

S-SM-P-329: Inspect Crosshair Stops

P510 Procedures:

S-SM-P-315: Clean P510 Streak Camera Optics

S-SM-P-330: P510 Water Chiller Level

HEDVAC Procedures:

S-SM-P-331: HEDVAC System Maintenance

S-SM-P-332: HEDVAC Pump Maintenance

This page last updated on 1 July 2008

Address document comments, questions, and corrections to the System Engineer.