OMEGA Laser Facility > Documentation > Volume III Subsystem and Component Maintenance > Section 1 Laser Drivers

OMEGA System Operations Manual - Volume III -- Subsystem and Component Maintenance (S-AA-M-014)

Front Matter - Maintenance Index & Schedules - S-OM-P-026

Laser Driver Subsystem Procedures:

S-SM-P-001: System-Wide Crate Reset
S-SM-P-002: Check for Ground Loops

S-SM-P-003: IR3 Calibration

S-SM-P-053: ACSLv2 Synchronization
S-SM-P-077: 15 GHz Scope Calibration
S-SM-P-081: PGR/DER HVAC Check

S-SM-P-161: Master Timing Generator Reset

Pulse Shaping Procedures:

S-SM-P-004: Mod Cal
S-SM-P-005: Min Cal
S-SM-P-006: Exercise Colby 10 Units
S-SM-P-007: Colby 40 Calibration
S-SM-P-008: 10V PSPL Calibration
S-SM-P-009: Koheras Output Power
S-SM-P-010: IFES Fiber Amplifier Energy & Waveform/Regen Injection
S-SM-P-011: IFES Fiber Amplifier Pump Diode Efficiency
S-SM-P-012: Inspect Modulator Cables

Regen Procedures:

S-SM-P-013: DPR Settings Check
S-SM-P-014: Diode Pumped Regen Mode-Coupled Energy Check
S-SM-P-015: DPR Cavity Alignment Check
S-SM-P-016: DPR Timing Check
S-SM-P-017: Regen Contrast Check
S-SM-P-018: DPR Output Energy Check
S-SM-P-019: Pockels Cell Voltage Check
S-SM-P-020: Output Collimation Check
S-SM-P-021: Regen Output Beam Ellipticity Check
S-SM-P-022: Driver Spatial Profile & Beam Size Check
S-SM-P-023: Bournlea Halfwave Voltage Output Check
S-SM-P-024: G6 Diode Battery Measurement
S-SM-P-025: Regen Energy Calibration
S-SM-P-026: Bias Voltage Check
S-SM-P-027: Beam Timing Support
S-SM-P-052: Replace Pockels Cell Driver

LARA Procedures:

S-SM-P-028: LARA Weekly Alignment
S-SM-P-029: LARA Monthly Alignment
S-SM-P-030: LARA Ring Pockels Cell Timing Check
S-SM-P-031: LARA Isolation Pockels Cell Timing Check
S-SM-P-032: LARA Ring Rail Contrast Ratio
S-SM-P-033: LARA Output Calibration
S-SM-P-034: LARA Hold-Off Test

Spatial Filter Procedures:

S-SM-P-035: Spatial Filter Pinhole Visual Inspection
S-SM-P-036: Spatial Filter Alignment Check
S-SM-P-037: LARA Spatial Filter Pinhole Centering
S-SM-P-038: Spatial Filter Pinhole Centering
S-SM-P-078: Spatial Filter Drive Belts

Optics Procedures:

S-SM-P-039: Inspect & Clean Optics

Smoothing by Spectral Dispersion Procedures:

S-SM-P-040: Modulation Check (MOD1)
S-SM-P-041: Modulation Check (MOD2)
S-SM-P-042: Halfwave Voltage Check on FID Pulser (SSD Slicer)

Driverline Procedures:

S-SM-P-043: Common Driver Faraday Rotator Contrast Measurement
S-SM-P-046: Backlighter Faraday Rotator Contrast Measurement

Output Quality Procedures:

S-SM-P-045: Driver Output Shear/Collimation Check

Fiducial Procedures:

S-SM-P-048: Fiducial ODR Injected Energy
S-SM-P-051: Fiber Output Energy

This page last updated on 26 February 2008

Address document comments, questions, and corrections to the LLE Lead System Engineer.